Every person may have their own individual thinking when it comes to Tools You Need to Install a New Bathtub .
Installing a bathtub isn't specifically brain surgery, however it does need solid plumbing, woodworking, as well as occasionally, tiling skills. Changing an old bath tub with a brand-new one is likewise a moderately difficult job. If the old tub is conveniently obtainable, the task can relocate immediately; if you have to open up a wall to get rid of the old bathtub and place the new bath tub, the task is much harder. In either situation, the job is within a home handyman's abilities, although you will need a helper to leave the old tub and embeded in the brand-new one. Ensure you have certified on your own for the work and are comfortable attempting it. Instead of working with a contractor to take over a halfway-completed project, it is much better to think about utilizing one before you begin. Chances are you may need a professional plumber to make tube connections.
This article will certainly aid you set up a new bathtub in your bathroom if you have actually currently purchased a new bathtub as well as don't require to alter the arrangement of your previous water pipelines.
Your tools and also material list must comprise the following:
Removing Old Touches
If you require to replace old faucets with new ones as a part of your setup, after that the first thing you must do is separate the water system. After doing so, activate the taps to drain any kind of water continuing to be in the system. The procedure of getting rid of the existing taps can be fairly troublesome because of the restricted gain access to that is often the instance.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipes to the taps. Have a towel all set for the remaining water that will come from the pipelines. When the supply pipes have been removed, make use of the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from turning throughout this process. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any kind of old sealing substance.
Before going on to fit the new faucets, compare the pipe links on the old taps to the new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.
Suitable New Touches
If the tails of the new taps are plastic, after that you will need a plastic port to stop damage to the thread. One end of the adapter fits on the plastic tail of the faucet and also the other end offers a connection to the existent supply pipes.
If you need to fit a monobloc, then you will certainly require lowering couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, place the tap in the placing hole in the bath/basin making certain that the washing machines are in location in between the tap as well as the sink. Protect the faucet in place with the manufacturer provided backnut. As soon as the tap is securely in position, the supply pipelines can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with regular faucet ports. The former type needs to be attached to the faucet ends initially, tightening up only by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Setting up the Bath tub
Utilizing the two wooden boards under its feet, position the tub in the called for position. The wood boards are helpful in uniformly spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto four little factors.
The next goal is to guarantee that the bath tub is leveled all round. This can be achieved by inspecting the level and also readjusting the feet on the bath tub up until the spirit level reads level.
To mount faucets, fit the bottom of the furthest flexible faucet port to the suitable supply pipe by making a compression sign up with; then do the same for the various other tap.
Switch on the water supply and also inspect all joints as well as new pipework for leakages as well as tighten them if necessary. Load the tub and additionally inspect the overflow electrical outlet and the regular outlet for leaks.
Lastly, fix the bathroom paneling as defined in the producer's user's manual. Tiling and also sealing around the tub must wait till the bathtub has been used a minimum of once as this will certainly settle it into its final placement.
Planning for the Installment
Firstly, the sustaining framework supplied with the bath needs to be fitted (if required) according to the supplier's guidelines. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is necessary to make certain that if the faucet comes with a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bath, it is also sensible to fit a supporting plate under the faucets device to stop stress on the bathtub.
Fit the adaptable faucet ports to the bottom of the two faucets using 2 nuts and also olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make sure you make use of every one of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath must now be ready to be fitted in its final position.
Tiling Around the Tub
In the location where the bathroom satisfies the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is important as the fitting can move sufficient to split a rigid seal, causing the water to penetrate the wall surface in between the bath and also the tiling, resulting in issues with dampness and also possible leakages to the ceiling below.
You can select from a range of coloured sealants to assimilate your fixtures and also fittings. They are offered in tubes and also cartridges, and also can sealing gaps approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with twists of soaked paper or soft rope. Remember to always load the bathtub with water prior to securing, to permit the motion experienced when the bathtub is in use. The sealer can fracture relatively early if you do not take into consideration this motion before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also easily offered on the marketplace. It is a good idea to fit the floor tiles making use of water-resistant or water-proof adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a passionate reader about Installing A Bathtub, I figured sharing that excerpt was a good idea. So long as you liked our blog entry please remember to pass it around. Thank you for taking the time to read it.
Pro assistance? Dial.